Zr對擠壓鑄造Al-5.0Cu-0.4Mn合金顯微組織和力學性能的影響
發布人：上海艾荔艾合金股份有限公司www.shailiai.cn
更新時間：2016-01-29
采用拉伸力學性能測試、宏觀腐蝕、掃描電鏡(SEM)、透射電鏡(TEM)等，研究不同Zr含量對擠壓鑄造Al-5.0Cu-0.4Mn合金顯微組織和力學性能的影響，并與重力鑄造的合金的顯微組織和力學性能進行對比分析。
Zr對擠壓鑄造Al-5.0Cu-0.4Mn合金顯微組織和力學性能的影響Effect of Zr on microstructures and mechanical properties of squeeze cast Al-5.0Cu-0.4Mn alloy采用拉伸力學性能測試、宏觀腐蝕、掃描電鏡(SEM)、透射電鏡(TEM)等，研究不同Zr含量對擠壓鑄造Al-5.0Cu-0.4Mn合金顯微組織和力學性能的影響，并與重力鑄造的合金的顯微組織和力學性能進行對比分析。結果表明：針對鑄態合金，無論是擠壓鑄造還是重力鑄造，在Zr含量(質量分?jǐn)?shù))為0.25%時，合金獲得最佳的抗拉強度、屈服強度和伸長率；而對于熱處理態合金，當Zr含量從0增加到0.35%時，合金的抗拉強度和屈服強度都隨著Zr含量的增加而增加，但伸長率在Zr含量為0.15%時達到最大值。擠壓鑄造可以顯著改善不同Zr含量合金的伸長率，但對鑄態合金伸長率的提升幅度明顯優于熱處理態合金的。Zr在鑄態合金中的強化作用主要是細晶強化，而合金經T6熱處理后，固溶強化以及Al3Zr粒子和θ?相的彌散強化是主要強化機制，擠壓鑄造可以顯著改善Al3Zr粒子的彌散強化效果。
The effect of Zr on the microstructures and mechanical properties of Al-5.0Cu-0.4Mn alloy prepared by squeeze casting was studied by tensile test, macro corrosion test, scanning electron microscopy (SEM), transmission electron microscopy (TEM), and took comparative analysis with the gravity cast alloy. The results show that the best tensile strength, yield strength and elongation are obtained for both the squeeze cast and gravity cast alloys in as-cast state when the Zr content is 0.25% (mass fraction). As for the heat-treated alloys, the tensile strength and yield strength increase when Zr content increases from 0 to 0.35%. However, the elongation reaches the maximum value when Zr content is 0.15%. Squeeze casting can significantly improve the elongation of the alloys with different Zr contents, but the improvement of the elongation of the as-cast alloys is significantly better than that of the heat-treated alloys. The dominant strengthening mechanism of Zr in the as-cast alloy is the grain refinement. However, the solid solution strengthening and dispersive strengthening of Al3Zr particles and q? phase are the main strengthening mechanisms in the alloy after T6 heat treatment. Squeeze casting can significantly improve the dispersion strengthening effect of Al3Zr particles.
作為值得信賴的合作伙伴和高品質金屬合金的半成品供應商，艾荔艾擁有完善的服務體系和專業的團隊。在同客戶交易的過程中，我們力求根據不同的應用需求將我們的產品做到精益求精。針對當前和未來的市場需求，艾荔艾致力于為客戶提供最佳的金屬材料解決方案。
AILIAI has been a reliable partner and supplier of sophisticated and high-quality semi-finished products maed of alloys. In dialogue with our customers, we optimise our products to meet the specific application requirements. AILIAI develops the best alloy material solutions for current and future challenges.
獲取更多我們供應的合金和服務信息，請致電086-021-67660801或發電子郵件[email protected]聯系我們，您也可以通過微博，微信，領英和推特與我們互動。
For more information on the alloys and services that we supply,?call us?at 086-021-67660801 or email us at [email protected]. You can also get in touch on social media, we are constantly active on?Weibo,?Weixin,?LinkedIn?and?Twitter.