新聞資訊
2A14合金的連續冷卻轉變動力學曲線及其應用
發布人：上海艾荔艾金屬材料有限公司bt990.com.cn
更新時間：2015-11-27
測定2A14合金連續冷卻轉變動力學曲線(CCT圖)，并對該曲線進行應用研究。通過DSC分析和SEM組織觀察確定2A14合金合理的固溶溫度，采用動態電阻法測得固溶后合金連續冷卻過程的電阻—溫度曲線，根據曲線斜率變化判斷相變信息，繪制2A14合金的CCT圖，利用透射電鏡(TEM)觀察連續冷卻過程中合金的組織轉變。
2A14合金的連續冷卻轉變動力學曲線及其應用Continuous cooling transformation curve for?2A14 aluminum alloy and its application
測定2A14合金連續冷卻轉變動力學曲線(CCT圖)，并對該曲線進行應用研究。通過DSC分析和SEM組織觀察確定2A14合金合理的固溶溫度，采用動態電阻法測得固溶后合金連續冷卻過程的電阻—溫度曲線，根據曲線斜率變化判斷相變信息，繪制2A14合金的CCT圖，利用透射電鏡(TEM)觀察連續冷卻過程中合金的組織轉變。結果表明：2A14合金適宜的固溶溫度為505 ℃；隨著冷卻速度的增加，相變開始溫度先降低，在達到某冷卻速度時驟升，然后持續增加；相變主要集中在140~380 ℃的溫度區間發生，抑制相變發生的臨界冷卻速度稍大于38.5 ℃/s；在實驗范圍內，20 mm厚的2A14合金板適宜采用60 ℃或100 ℃水淬，參考所測CCT圖制定分級淬火工藝，可以在最大限度減小淬火應力的同時，抑制第二相的析出。
The continuous cooling transformation (CCT) curve of 2A14 aluminum alloy and its application were studied. The solutionizing temperature was ascertained by DSC analysis and SEM observation. Electrical resistance—temperature curves of 2A14 alloy in the continuous cooling processes after solid solution treatment were obtained by in-situ resistance measurement. Messages of the phase transformation were judged by analyzing the slope change of the obtained curves. The CCT diagram for Al-Cu-Mg alloy was plotted. The microstructure evolution during the cooling was examined by TEM observation. The results show that the appropriate solid solution temperature is 505 ℃. The phase transformation starting temperature decreases with the increase of cooling rates when the cooling rate is slow, but when the cooling rate is a little higher the phase transformation starting temperature increases suddenly. The phase transformation mainly takes place between 140 and 380 ℃. The critical cooling rate for preventing the phase transformation is above 38.5 ℃/s. It is better for 2A14 plates with the thickness of 20 mm to quench by 60 ℃ or 100 ℃ water. Interrupted quenching process can be established according to the tested CCT diagram to decrease quenching stress utmost and inhibit the precipitation of the secondary phases at the same time.
?以上資料由上海艾荔艾金屬材料有限公司提供，歡迎新老客戶來電洽購。
本文來自上海艾荔艾金屬材料有限公司http://bt990.com.cn，轉載請注明出處。
前一頁：淬火介質對7050鋁合金末端淬特性的影響
后一頁：7039鋁合金靶板侵徹過程中的組織特征及數值模擬