新聞資訊
淬火介質對7050鋁合金末端淬特性的影響
發布人：上海艾荔艾金屬材料有限公司bt990.com.cn
更新時間：2015-11-27
采用室溫水和濃度為20%的PAG水溶液 (聚烷撐二醇聚合物)作為淬火介質進行Jominy末端淬火實驗，用于評價7050鋁合金淬透性；監測合金固溶和淬火過程中的升溫速率和冷卻速率，測定距淬火端不同距離的合金的淬火態電導率和時效態硬度，觀察室溫水淬火試樣不同位置晶內淬火析出相。
淬火介質對7050鋁合金末端淬特性的影響Effect of quenching media on?Jominy end quench behavior of 7050 Al alloy
采用室溫水和濃度為20%的PAG水溶液 (聚烷撐二醇聚合物)作為淬火介質進行Jominy末端淬火實驗，用于評價7050鋁合金淬透性；監測合金固溶和淬火過程中的升溫速率和冷卻速率，測定距淬火端不同距離的合金的淬火態電導率和時效態硬度，觀察室溫水淬火試樣不同位置晶內淬火析出相。結果表明：采用室溫水和20%PAG進行末端淬火時，合金的淬透深度分別約為65和40 mm；采用PAG淬火可使合金溫度快速通過淬火敏感區間，同時在淬火敏感區間外降低合金的冷卻速率，使試樣淬火端和中間部位合金的溫度差減小。隨著距淬火端距離的增加，淬火誘發析出的η平衡相的尺寸和體積分?jǐn)?shù)增加，無析出區寬化。
The Jominy end quench test was used to evaluate the hardenability of 7050 Al alloys. The room-temperature water and 20%PAG were adopted as quenching media respectively in this test. The heating and cooling rates of the 7050 bar were monitored. The as-aged hardness and as-quenched electrical conductivity of alloys at different distances from the quenched end were collected, and the intragranular precipitates at different locations of samples quenched by room-temperature water were observed. The results indicate that the quenched depths of the alloy are 65 and 40 mm for the alloy quenched by room-temperature water and 20%PAG, respectively. The alloy can pass through the quench sensitive temperature range rapidly when quenched by 20%PAG, the cooling rate can be reduced outside that range, and the temperature difference between the quenched end and center parts of the quenched bar is decreased. The size and volume fraction of the quench induced equilibrium η phase as well as the width of the PFZs increase with the distance from the quenched end increasing.
?以上資料由上海艾荔艾金屬材料有限公司提供，歡迎新老客戶來電洽購。
本文來自上海艾荔艾金屬材料有限公司http://bt990.com.cn，轉載請注明出處。
前一頁：基于應變影響的7A09鋁合金等溫壓縮流動應力模型
后一頁：2A14合金的連續冷卻轉變動力學曲線及其應用