新聞資訊
Ti-5Al-5Mo-5V-1Cr-1Fe合金的高溫塑性變形行為
發布人：上海艾荔艾金屬材料有限公司bt990.com.cn
更新時間：2015-10-17
在Gleeble-1500 熱模擬機上對Ti-5Al-5Mo-5V-1Cr-1Fe合金進行高溫?zé)釅嚎s實驗，研究該合金在變形溫度為750~900 ℃、應變速率為0.001~1 s?1 條件下的流變應力行為。利用光學顯微鏡分析合金在不同變形條件下的組織演化規律。
Ti-5Al-5Mo-5V-1Cr-1Fe合金的高溫塑性變形行為Plastic deformation behavior of Ti-5Al-5Mo-5V-1Cr-1Fe alloy at high temperature
在Gleeble-1500 熱模擬機上對Ti-5Al-5Mo-5V-1Cr-1Fe合金進行高溫?zé)釅嚎s實驗，研究該合金在變形溫度為750~900 ℃、應變速率為0.001~1 s?1?條件下的流變應力行為。利用光學顯微鏡分析合金在不同變形條件下的組織演化規律。結果表明：合金的流變應力隨著應變速率的增大和變形溫度的降低而增大；流變應力隨著應變的增加而增大，出現峰值后逐漸趨于平穩；變形過程中的流變應力可用Arrhenius雙曲正弦本構關系來描述，平均變形激活能為454.2 kJ/mol；各種變形條件均可細化原始晶粒尺寸。隨著溫度的升高和應變速率的降低，合金的主要軟化機制由動態回復逐漸變?yōu)閯?dòng)態再結晶；在(α+β)相區變形(750~850 ℃)時，α相對β晶粒的動態再結晶的發生起到阻礙作用。
The hot deformation behaviors of Ti-5Al-5Mo-5V-1Cr-1Fe alloy were studied by a Gleeble-1500 machine at 750?900 ℃ with the strain rate of 0.001?1 s?1. The microstructural evolution of the alloy was investigated by optical microscopy. The results indicate that the flow stress of the alloy increases with increasing strain rate and decreasing deformation temperature. The flow stress increases with increasing strain until the stress reaches the peak value, then the flow stress remains constant. The flow stress in deformation can be described by Arrhenius hyperbolic sine constitutive equation, and the average activation energy is 454.2 kJ/mol. The original grain size can be refined under all deformation conditions. The main softening mechanism is changed from dynamic recovery to dynamic recrystallization with increasing the deformation temperature and decreasing the strain rate. In the (α+β) region (750?850 ℃), α phase can inhibit the dynamic recrystallization of β grains particles during deformation.
以上資料由上海艾荔艾金屬材料有限公司提供，歡迎新老客戶來電洽購。
本文來自上海艾荔艾金屬材料有限公司http://bt990.com.cn，轉載請注明出處。