新聞資訊
Ti6321鈦合金退火處理過程中組織演變及其對沖擊韌性的影響
發布人：上海艾荔艾金屬材料有限公司bt990.com.cn
更新時間：2015-09-11
為了調整合金顯微組織參量，提高沖擊韌性，采用OM研究Ti6321合金退火處理過程中組織演變及其對沖擊韌性αkv的影響。
Ti6321鈦合金退火處理過程中組織演變及其對沖擊韌性的影響Microstructure evolution of Ti6321 titanium alloy during annealing treatment and its effect on impact toughness
為了調整合金顯微組織參量，提高沖擊韌性，采用OM研究Ti6321合金退火處理過程中組織演變及其對沖擊韌性αkv的影響。結果表明：Ti6321合金沖擊韌性隨退火溫度和時間發生明顯變化。當退火溫度低于Tβ時，初生等軸α相晶粒尺寸和次生條狀α相寬度隨退火溫度升高而增大，次生α相條長寬比減小，使Ti6321合金沖擊韌性αkv顯著提高。當退火溫度高于Tβ時，退火后初生等軸α相減少，β相含量急劇增加，空冷時從β相中析出大量針狀次生α相，次生α相條長寬比增大，使合金沖擊韌性αkv下降。在2 h內隨退火時間延長，次生α相條粗化，長寬比降低，沖擊韌性上升；退火時間超過2 h后，合金組織和沖擊韌性趨于穩定。
The microstructure evolution and its effects on impact toughness of Ti6321 titanium alloy were investigated by the OM in order to enhance the impact toughness by changing microstructure through adjusting annealing temperature. The results indicate that the impact toughness greatly changes with the increase of annealing temperature. When the annealing temperature is lower than tβ, exquiaxed primary α grain and the secondary α lath grow up with annealing temperature increasing, and the impact toughness is remarkably enhanced. However, when annealing temperature is higher than tβ, exquiaxed primary α phase is reduced, and β phase contents rapidly increase. Large numbers of needle-like secondary α phases precipitate from β phase during air cooling, and the ratio of length to width of secondary α lath increases, which makes the impact toughness decrease. Within 2 h, secondary α lath coarsen and the ratio of length to width decreases with increase of annealing time, and then impact toughness increases. When annealing time is longer than 2 h, the microstructure and impact toughness are unchanged with annealing time prolonging.
以上資料由上海艾荔艾金屬材料有限公司提供，歡迎新老客戶來電洽購。
本文來自上海艾荔艾金屬材料有限公司http://bt990.com.cn，轉載請注明出處。