新聞資訊
7050-T7452鍛件模擬高溫服役環境下組織性能的演化
發布人：上海艾荔艾金屬材料有限公司bt990.com.cn
更新時間：2015-08-24
通過拉伸試驗和微觀組織觀察等方法對經過不同溫度和時間模擬高溫服役環境熱暴露處理后7050-T7452鍛件的室溫拉伸性能以及合金金相組織、析出相的變化情況進行系統研究。
7050-T7452鍛件模擬高溫服役環境下組織性能的演化Evolution of microstructure and properties of 7050-T7452
alloy forging simulation in high temperature service environment
通過拉伸試驗和微觀組織觀察等方法對經過不同溫度和時間模擬高溫服役環境熱暴露處理后7050-T7452鍛件的室溫拉伸性能以及合金金相組織、析出相的變化情況進行系統研究。結果表明：7050-T7452鍛件在100~
175 ℃下熱暴露處理后，合金的強度隨熱暴露溫度的提高和時間的延長而降低，伸長率隨之增加；當熱暴露溫度超過125
℃后，變化更為明顯；隨熱暴露溫度和時間的變化，合金的晶粒尺寸以及再結晶程度沒有明顯改變；當熱暴露溫度≤125
℃時，合金晶粒內部析出相的尺寸和種類沒有明顯變化；隨熱暴露時間的增加，晶界無析出帶的寬度略有增寬；當熱暴露溫度超過125
℃時，合金晶內的析出相隨溫度以及熱暴露時間的增加而迅速粗化，η相的體積分?jǐn)?shù)增加，晶界無析出帶加寬，合金的強度明顯下降。
The evolution of microstructure and properties of
7050-T7452 alloy forging simulation in high temperature service environment for
different times and temperatures was studied by tensile test and transmission
electron microscopy．The results show that the strength of 7050-T7452 alloy
forging decreases with the thermal exposed time and temperature increasing in
the range of 100-175 ℃, however, the elongation increases. The change of
strength is obvious when the exposed temperature is higher than 125 ℃, and the
change of grain size and recrystallization is not obvious. When the exposed
temperature is lower than 125 ℃, the sizes and species of precipitates do not
change obviously. The width of precipitate-free zones (PFZs) increases a little
with the exposed time increasing. When the exposed temperature is higher than
125 ℃, the precipitates in matrix are coarser with the exposed temperature and
time increasing. Meanwhile, the precipitate size and width of PFZs increase
obviously, and the dominant precipitate is η phase. The strength of alloy
decreases visibly in this period.
以上資料由上海艾荔艾金屬材料有限公司提供，歡迎新老客戶來電洽購。
本文來自上海艾荔艾金屬材料有限公司http://bt990.com.cn，轉載請注明出處。